Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
   1.1. Introduction
   1.2. The panel of devices
   1.3. The ignition lock
   1.4. The combined switch
   1.5. The emergency light alarm system
   1.6. Switches of the panel of devices
   1.7. Cruise-control
   1.8. Devices and control lamps
   1.9. Control levers
   1.10. Windows and стеклоподъемники
   1.11. Salon illumination
   1.12. An electric digital watch
   1.13. Controls heating and the fan or the conditioner
      1.13.1. Recommendations about work with the conditioner
   1.14. Driving
   1.15. Release of air from fuel system
   1.16. Опорожнение a water separator
   1.17. Regular checks
   1.18. Service of the air filter
   1.19. Engine oil replacement
   1.20. The block of safety locks
   1.21. Technical characteristics
2. Maintenance service
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> The maintenance instruction>> Controls heating and the fan or the conditioner

1.13. Controls heating and the fan or the conditioner
THE GENERAL DATA

Heating / the fan

 

 

1 – the switch-lever
2 – the temperature lever
3 – the switch the fan

4 – the switch "external air / internal circulation"


The switch-lever

 

The switch can be moved in different positions, setting corresponding operating modes.

The same switch it is possible to include and the refrigerator compressor.

The fan switch

 

The switch sets speed of the fan.

HEATING

Heating

 

The lever on "HOT", and the switch on "HEAT".

Air temperature can be changed moving the temperature lever between "COLD" and "HOT".

Establish the fan switch on a desirable stream.

Two levels

 

The lever is translated in this position when it is necessary to direct warm air to feet.

If the lever in position "BI-LEVEL" it is necessary to translate the temperature lever on the middle between "COLD" and "HOT".

The fan switch thus can be in any position according to your desire.

Defrosting and windscreen drainage

 

Establish the temperature lever on "COLD", and the switch on "DEF" to drain glass. The fan switch translate in position "3" or "HI".

 

That to drain or defreeze glass in the winter, the temperature lever put on "NOTES", and the switch – on "НЕАТ".

Allow to system to work approximately 30 сек for self-drainage, then translate the switch in position "DEF", and the fan switch – on "3" or "HI".

Airing

 

To direct external air directly to salon, translate the t-lever on "COLD", and the switch in position "VENT".

The fan adjust at will.

"OFF" – it is switched off

 

In this position the fan does not work, but during driving external air nevertheless arrives in salon through ventilating apertures.

The switch "external air / internal circulation"

If to press the top part of the switch fresh air does not move outside, and there is an air circulation in salon (for fast heating or not to let in a dust).

If to press the bottom part of the switch, fresh air arrives.

THE CONDITIONER

"MOVE" – a maximum

Air from salon mixes up with a small amount of fresh air, is processed and again goes to salon through ventilating apertures.

In this position of the t-lever, i.e. the lever on "COLD", it is possible to reach the maximum cooling at heats and humidity.

"NORM" – norm
External air is processed at passage through system and moves in salon through ventilating apertures.

Double level
External air is processed and spent through ventilating apertures.

This position of the lever provides comfort and supports a windscreen normal state.