Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
   2.1. The data on car identification
   2.2. The general data of engines
   2.3. THAT of cars Trooper/Bighorn with the diesel engine
   2.4. Instructions on leaving
      2.4.1. The air filter
      2.4.2. The fuel filter (petrol engines)
      2.4.3. The fuel filter (diesel engines)
      2.4.4. Draining of the water which have collected in fuel system of the diesel engine
      2.4.5. Compulsory system of ventilation картера (PCV-system)
      2.4.6. A tank for catching of steams of gasoline
      2.4.7. Features of check of system of catching of steams
      2.4.8. The storage battery
      2.4.9. Drive belts
      2.4.10. Cooling system
      2.4.11. A central air
      2.4.12. A screen wiper
      2.4.13. Recommended marks of fuel and oil
      2.4.14. Care of a manual transmission or automatic transmission
      2.4.15. Check of level of oil or a liquid
      2.4.16. Oil replacement
      2.4.17. Carter of a distributing box
      2.4.18. A reducer of the back bridge
      2.4.19. A cooling liquid
      2.4.20. The main brake cylinder
      2.4.21. The main cylinder of a hydrodrive of coupling
      2.4.22. A nutritious tank of the hydraulic booster of a wheel
      2.4.23. A reducer of the steering mechanism
      2.4.24. Running gear greasing
      2.4.25. Body greasing
      2.4.26. Greasing of the mechanism of a manual brake
      2.4.27. Greasing of draught of a drive throttle заслонки
      2.4.28. Greasing of the lever of a gear change
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes

Isuzu Trooper>> Maintenance service>> Instructions on leaving>> Screen wiper

2.4.12. A screen wiper

For prolongation of service life of a screen wiper it is necessary to delete from a windscreen the pollution caused by hit of leaves, tar from a road covering, etc. which lead to the strengthened deterioration of rubber brushes. Rubber scrapers are replaced in process of their deterioration, as a rule, annually. In necessity of their replacement specify bad removal of water, non-uniform прилегание or the raised gnash at screen wiper work.

It is expedient to replace brushes in steam.

Replacement of brushes

1 – the lever щеткодержателя
2 – a rubber scraper of a brush
3 – squeeze огранитель on each side
4 – lever sponges
5 – unclench
6 – wider metal substrate щеткодержателя
7 – terminators
8 – скоба the lever
9 – an edging of a metal substrate
10 – keep against перекручивания
11 – полосковя a metal substrate
12 – hook a screw-driver
13 – sponges
14 – the hinge
15 – the brush is deduced from the lock
16 – the brush is fixed
17 – a plastic substrate
18 – a groove
19 – скоба
20 – a brush scraper
21 – press
22 – tighten and turn
23 – a teeth of clamps
24 – at edges of brushes of type TRIDON the numbers specifying their length (16 are cast and 16,5), new brushes or scrapers should be precisely same length
25 – a firm surface

1. For removal of a rubber brush it is necessary to insert under spring скобу a screw-driver and to turn.
2. Displace a brush and get it from terminators.
3. To insert a new brush it is necessary to get it in gearing with terminators in щеткодержателе, to combine a groove in a scraper with a ledge on щеткодержателе and to fix a brush.