Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
         3.2.1.1. The ignition coil
         3.2.1.2. The ignition block
         3.2.1.3. The induction gauge of ignition for engines V6
         3.2.1.4. The ignition distributor
         3.2.1.5. System of a charge of the battery
         3.2.1.6. System of start-up of the engine
            3.2.1.6.1. The storage battery
            3.2.1.6.2. A starter
            3.2.1.6.3. The traction relay of a starter
            3.2.1.6.4. A starter without a reducer
            3.2.1.6.5. A starter with a reducer
      3.2.2. Major repairs of engines
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Electric equipment of engines>> System of start-up of the engine>> Starter without a reducer

3.2.1.6.4. A starter without a reducer
THE GENERAL DATA

Details of the device of a starter (without a reducer, 4-cylinder engines)

1 – the M conclusion
2 – bolts of fastening of a forward cover
3 – the traction relay in gathering
4 – a sealant
5 – a spiral spring of the traction relay
6 – a coupling bolt
7 – a forward cover
8 – the forward bearing of an anchor
9 – a sealant
10 – the lever of a drive of a starter
11 – a sealant
12 – a washer and a lock ring
13 – the screw of fastening of a back cover
14 – a back cover in gathering
15 – the back bearing of an anchor
16 – a brush of a positive conclusion
17 – щеткодержатель
18 – the starter case in gathering with excitation windings
19 – a lock ring of the restrictive plug
20 – the restrictive plug
21 – a drive gear wheel in gathering with обгонной муфтой
22 – an anchor in gathering

Details of the device of a starter (without a reducer, 6-cylinder engines)

1 – a nut
2 – the screw of fastening of the traction relay
3 – скоба the traction relay
4 – the traction relay
5 – a spring плунжера the traction relay
6 – a coupling bolt
7 – a back cover
8 – a spring щеткодержателя
9 – муфта in gathering with a leading gear wheel
10 – an anchor
11 – плунжер the traction relay
12 – the lever of a drive of a starter
13 – a persistent washer
14 – a lock ring
15 – the restrictive plug
16 – щеткодержатель
17 – an anchor

Dismantling and assemblage

PERFORMANCE ORDER
1. Clamp a starter in a vice with soft sponges. Disconnect from the traction relay a wire from an excitation winding.
2. Turn away screws of fastening of the traction relay and remove the relay from the lever of a drive of a starter.
3. Remove a forward cover, get from an anchor shaft a persistent ring, a washer, a spring and a sealant.
4. Turn on and get bolts of fastening of a back cover of a starter (from outside a collector), uncover, a brush and a contact plate.
5. Remove the starter case in gathering with excitation windings. Remove a bolt of an axis of the lever of a drive, a rubber sealant and a plate.
6. Get from a forward cover an anchor and the lever of a drive of a starter. Press from a lock ring the restrictive plug, then remove a lock ring, the restrictive plug and a drive gear wheel in gathering with обгонной муфтой.
7. If brushes are worn out on 1/2 from initial height, or strongly polluted by oil brushes replace. Height of new brushes of 16 mm.
8. It is not supposed to wash out муфту a starter solvent as the put greasing can be removed. Dress on a shaft of an anchor a drive gear wheel in gathering with обгонной муфтой, and, keeping an anchor, turn муфту.
The prevention

The gear wheel together with муфтой should rotate without jammings only in one direction. Smooth rotation with a small friction, but without notable jamming is supposed. Otherwise муфта in gathering with a gear wheel is subject to replacement. Муфту it is necessary to replace and at detection of wear tracks on gear wheel teeths.


9. Grease консистентной with greasing шлицы and an anchor shaft.
10. Establish муфту, the restrictive plug, a lock ring and the lever of a drive of a starter on an anchor.
11. Insert the collected anchor into a forward cover.
12. Put on the starter case in gathering with excitation windings an anchor and insert into a forward cover.
13. Insert brushes and dress щеткодержатель on an anchor collector.
14. Establish a back cover of a starter and wrap coupling bolts.
15. Establish a lining, an anchor spring, a washer and a sealant.