Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
         3.2.1.1. The ignition coil
         3.2.1.2. The ignition block
         3.2.1.3. The induction gauge of ignition for engines V6
         3.2.1.4. The ignition distributor
         3.2.1.5. System of a charge of the battery
         3.2.1.6. System of start-up of the engine
            3.2.1.6.1. The storage battery
            3.2.1.6.2. A starter
            3.2.1.6.3. The traction relay of a starter
            3.2.1.6.4. A starter without a reducer
            3.2.1.6.5. A starter with a reducer
      3.2.2. Major repairs of engines
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Electric equipment of engines>> System of start-up of the engine>> Starter with a reducer

3.2.1.6.5. A starter with a reducer
THE GENERAL DATA

Details of the device of a starter with a reducer

1 – a conclusion of a winding of excitation
2 – a coupling bolt
3 – a starter in gathering with windings of excitation and the case
4 – a back cover of the case
5 – щеткодержатель
6 – an anchor
7 – a forward cover
8 – шестеренчатая муфта
9 – a returnable spring
10 – a ball
11 – an intermediate gear wheel
12 – the persistent bearing

Dismantling and assemblage

PERFORMANCE ORDER
1. Clamp a starter in a vice with soft sponges. Turn away a nut and disconnect the plug of a winding of excitation of a starter from a conclusion of the traction relay.
2. Turn away coupling bolts and get the case with windings of excitation and an anchor from the traction relay.
3. Turn away bolts of fastening of a forward cover of a starter to the case of the traction relay and remove the case. Remove a reducer gear wheel, persistent bearings and conducted шестеренчатую муфту in gathering.
4. By means of the magnetised tool get a spring with a ball from an aperture inside шестеренчатой муфты. Remove a back cover of the case of a starter.
5. Raise a screw-driver of a spring of brushes, get brushes from щеткодержателя and get щеткодержатель from the case with excitation windings.
6. Get an anchor from the case with windings. Check up resistance of isolation between a collector and the anchor core. If there is a collector short circuit on the core an anchor replace.
7. Check up integrity of a chain between collector plugs. If there is a rupture between at least two plugs an anchor replace.
8. If the collector is polluted, on plugs there are traces подгорания or if palpation exceeds 0,05 mm, прошлифуйте a collector on a lathe. Limiting diameter of a collector of 29,0 mm.
9. Check up integrity of a chain between conclusions of a winding of excitation (the tyre leaving a skeleton and щеточным by a conclusion). If in a chain there is a rupture a skeleton with windings replace.
10. Check up a chain between a skeleton and windings. At short circuit a skeleton with windings replace.
11. Replace brushes, if their height less than 10 mm.
12. Check up a condition of teeths of a gear wheel. In the presence of strong damages of a gear wheel replace. Check up rotation freedom муфты in gathering with a gear wheel, having turned it clockwise. The gear wheel should not rotate counter-clockwise. Otherwise муфту in gathering with a gear wheel replace.
13. Press on the bearing and check up rotation freedom. If strong resistance to rotation the bearing replace is marked.
14. Check up a chain between mass and isolated by conclusions, then between a mass conclusion and the case. If rupture the traction relay in gathering replace is found out.
15. Grease gear wheels, shaft and bearings with high-temperature greasing.
16. Establish in the case шестеренчатую муфту, a gear wheel and persistent bearings.
17. Establish a spring, a ball, collect the traction relay with a forward cover.
18. Establish brushes in щеткодержатель, be convinced that conclusions of positive brushes do not concern cases.
19. Establish a back cover.
20. Establish the case with excitation windings on the traction relay, having combined a ledge on the case with a groove on the traction relay.
21. Further assemblage is carried out upside-down.