Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
      3.2.2. Major repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and engine repair
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. A cover of a head of cylinders
         3.2.2.5. Коромысла and platens коромысел
         3.2.2.6. The thermostat
         3.2.2.7. A soaking up collector
         3.2.2.8. A final collector
         3.2.2.9. Турбокомпрессор
         3.2.2.10. The conditioner
         3.2.2.11. A radiator
         3.2.2.12. The fan of system of cooling with a drive from the electric motor
         3.2.2.13. The pump of a cooling liquid
         3.2.2.14. A head of cylinders
         3.2.2.15. Valves and springs
            3.2.2.15.1. Check of springs
            3.2.2.15.2. Directing plugs of valves
            3.2.2.15.3. Saddles of valves
            3.2.2.15.4. Grinding in of valves
         3.2.2.16. Pushers
         3.2.2.17. The oil pallet
         3.2.2.18. The oil pump
         3.2.2.19. An epiploon of a forward cover of a gear belt
         3.2.2.20. A chain of a drive of a camshaft and a drive asterisk
         3.2.2.21. A forward cover of a gear belt
         3.2.2.22. An epiploon of a cranked shaft
         3.2.2.23. A gear belt and натяжитель
         3.2.2.24. A gear belt and the tension mechanism
         3.2.2.25. A drive газораспределительного the mechanism petrol engines
         3.2.2.26. A drive газораспределительного the mechanism diesel engines
         3.2.2.27. A camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Shatunnye bearings
         3.2.2.31. Assemblage of shatunno-piston group and installation on the engine
         3.2.2.32. Заглушки and a heater картера the engine
         3.2.2.33. A back epiploon of a cranked shaft
         3.2.2.34. A cranked shaft and radical bearings
         3.2.2.35. A flywheel and a gear wreath
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Major repairs of engines>> Valves and springs>> Grinding in of valves

3.2.2.15.4. Grinding in of valves
THE GENERAL DATA

It is necessary for maintenance tight прилегания valve heads to a saddle. It is carried out after repair (repolishing) of saddles and heads of valves or if valves and saddles are in a satisfactory condition.

PERFORMANCE ORDER
1. Put a head combustion chambers upwards.
2. On facets of valves apply a thin film pure oil, and on saddles After grinding in remove the adaptation and carefully remove the abrasive rests, having washed out all head in solvent. A layer притирочной pastes. Establish the valve in a corresponding saddle (being guided on the labels put at dismantling).
3. For grinding in the adaptation sucker is attached to a valve head (connected to a manual drill, a mixer and др). The valve gets used circular motions until the saddle surface does not become polished (in process of grinding in it can be necessary to add притирочную paste).
4. After grinding in remove the adaptation and carefully remove the abrasive rests, having washed out all head in solvent.