Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
      3.2.2. Major repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and engine repair
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. A cover of a head of cylinders
         3.2.2.5. Коромысла and platens коромысел
         3.2.2.6. The thermostat
         3.2.2.7. A soaking up collector
         3.2.2.8. A final collector
         3.2.2.9. Турбокомпрессор
         3.2.2.10. The conditioner
         3.2.2.11. A radiator
         3.2.2.12. The fan of system of cooling with a drive from the electric motor
         3.2.2.13. The pump of a cooling liquid
         3.2.2.14. A head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. The oil pallet
         3.2.2.18. The oil pump
         3.2.2.19. An epiploon of a forward cover of a gear belt
         3.2.2.20. A chain of a drive of a camshaft and a drive asterisk
         3.2.2.21. A forward cover of a gear belt
         3.2.2.22. An epiploon of a cranked shaft
         3.2.2.23. A gear belt and натяжитель
         3.2.2.24. A gear belt and the tension mechanism
         3.2.2.25. A drive газораспределительного the mechanism petrol engines
         3.2.2.26. A drive газораспределительного the mechanism diesel engines
         3.2.2.27. A camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Shatunnye bearings
         3.2.2.31. Assemblage of shatunno-piston group and installation on the engine
         3.2.2.32. Заглушки and a heater картера the engine
         3.2.2.33. A back epiploon of a cranked shaft
         3.2.2.34. A cranked shaft and radical bearings
         3.2.2.35. A flywheel and a gear wreath
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Major repairs of engines>> Drive газораспределительного the mechanism petrol engines

3.2.2.25. A drive газораспределительного the mechanism of petrol engines

ENGINES 4ZD1 AND 4ZE1

Camshaft asterisk

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove a gear belt.
3. Turn away a bolt and remove a camshaft asterisk. To facilitate asterisk removal cautiously knock on it with a hammer and get moving forward.
4. Remove a camshaft epiploon (which is subject to replacement).

Installation

PERFORMANCE ORDER
1. Combine labels on an asterisk of a camshaft and on a back cover of a gear belt, establish an asterisk. Put on a belt.
2. Bring a roller натяжителя to a belt that the roller has rested against a belt under the influence of a spring.
3. Turn a cranked shaft on 2 complete revolutions in a direction opposite to normal rotation and be convinced that adjusting labels have again coincided.
4. Release a roller bolt натяжителя that the belt has stretched under the influence of a spring. Tighten a bolt of a roller with the moment 22 Н.м.
5. Establish covers of a gear belt and a pulley of a cranked shaft.
6. Connect the battery to weight, start the engine and be convinced of absence of a leak.

Leading asterisk of a cranked shaft

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove a gear belt.
3. Turn away a bolt and by means of a stripper remove an asterisk of a cranked shaft.
4. Remove an epiploon of a cranked shaft (which is subject to replacement).

Installation

PERFORMANCE ORDER
1. Combine labels on a leading asterisk of a cranked shaft and on a cover of the holder of an epiploon.
2. Check up combination of adjusting labels of a camshaft and dress a belt.
3. Bring a roller натяжителя to a belt that the roller has rested against a belt under the influence of a spring.
4. Turn a cranked shaft on 2 complete revolutions in a direction opposite to normal rotation and be convinced that adjusting labels have again coincided.
5. Release a roller bolt натяжителя that the belt has stretched under the influence of a spring. Tighten a bolt of a roller with the moment 22 Н.м.
6. Establish covers of a gear belt and a pulley of a cranked shaft.
7. Other procedures are carried out upside-down.