Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
      3.2.2. Major repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and engine repair
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. A cover of a head of cylinders
         3.2.2.5. Коромысла and platens коромысел
         3.2.2.6. The thermostat
         3.2.2.7. A soaking up collector
         3.2.2.8. A final collector
         3.2.2.9. Турбокомпрессор
         3.2.2.10. The conditioner
         3.2.2.11. A radiator
         3.2.2.12. The fan of system of cooling with a drive from the electric motor
         3.2.2.13. The pump of a cooling liquid
         3.2.2.14. A head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. The oil pallet
         3.2.2.18. The oil pump
         3.2.2.19. An epiploon of a forward cover of a gear belt
         3.2.2.20. A chain of a drive of a camshaft and a drive asterisk
         3.2.2.21. A forward cover of a gear belt
         3.2.2.22. An epiploon of a cranked shaft
         3.2.2.23. A gear belt and натяжитель
         3.2.2.24. A gear belt and the tension mechanism
         3.2.2.25. A drive газораспределительного the mechanism petrol engines
         3.2.2.26. A drive газораспределительного the mechanism diesel engines
         3.2.2.27. A camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Shatunnye bearings
         3.2.2.31. Assemblage of shatunno-piston group and installation on the engine
         3.2.2.32. Заглушки and a heater картера the engine
         3.2.2.33. A back epiploon of a cranked shaft
         3.2.2.34. A cranked shaft and radical bearings
         3.2.2.35. A flywheel and a gear wreath
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Major repairs of engines>> Assemblage of shatunno-piston group and installation on the engine

3.2.2.31. Assemblage of shatunno-piston group and installation on the engine
PERFORMANCE ORDER
1. Сориентируйте on labels a rod and the piston.
2. Grease a piston finger with pure oil for the engine and enter into the piston and a rod, or having pushed by hand, or запрессовав on the adaptation (depending on a design).
3. Establish lock rings of fingers (if are provided), having turned them so that rings were fixed in special flutes.
4. Further arrive as follows.
5. Be convinced of correct selection шатунных loose leaves and in correct mutual orientation of the piston and a rod.
6. Dress on bolts of covers pieces of a rubber hose, grease loose leaves шатунных bearings with assembly greasing.
7. Compress rings and enter the piston in gathering with a rod into the cylinder (dredging in the top part of the piston should be turned towards a forward part of the engine).
8. Grease шатунные necks of a cranked shaft with assembly greasing or pure oil for the engine. Enclose the loose leaf in a rod and draw a rod to corresponding шатунной to a neck.
9. Remove pieces of hoses, establish covers of rods and tighten bolts (nuts) of rods with the set moment.
10. Check up a backlash between end faces of rods and cranked shaft. For backlash measurement it is necessary to take away a rod slightly. If the backlash is less than norm the rod follows прошлифовать. If the backlash exceeds norm replace a rod new and again check up a backlash. If the backlash still exceeds standard the cranked shaft should be removed, welded on and прошлифовать, or to replace.
11. Establish the oil pump (if acted in film) and the oil pallet.
12. Establish a head of the cylinders, soaking up collector (subsection 3.2.2.7 and subsection 3.2.2.14.1 see).