Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
      3.2.2. Major repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and engine repair
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. A cover of a head of cylinders
         3.2.2.5. Коромысла and platens коромысел
         3.2.2.6. The thermostat
         3.2.2.7. A soaking up collector
         3.2.2.8. A final collector
         3.2.2.9. Турбокомпрессор
         3.2.2.10. The conditioner
         3.2.2.11. A radiator
         3.2.2.12. The fan of system of cooling with a drive from the electric motor
         3.2.2.13. The pump of a cooling liquid
         3.2.2.14. A head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. The oil pallet
         3.2.2.18. The oil pump
         3.2.2.19. An epiploon of a forward cover of a gear belt
         3.2.2.20. A chain of a drive of a camshaft and a drive asterisk
         3.2.2.21. A forward cover of a gear belt
         3.2.2.22. An epiploon of a cranked shaft
         3.2.2.23. A gear belt and натяжитель
         3.2.2.24. A gear belt and the tension mechanism
         3.2.2.25. A drive газораспределительного the mechanism petrol engines
         3.2.2.26. A drive газораспределительного the mechanism diesel engines
         3.2.2.27. A camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Shatunnye bearings
         3.2.2.31. Assemblage of shatunno-piston group and installation on the engine
         3.2.2.32. Заглушки and a heater картера the engine
         3.2.2.33. A back epiploon of a cranked shaft
         3.2.2.34. A cranked shaft and radical bearings
         3.2.2.35. A flywheel and a gear wreath
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Major repairs of engines>> Back epiploon of a cranked shaft

3.2.2.33. A back epiploon of a cranked shaft
THE GENERAL DATA

Back integral epiploon of a cranked shaft

Integral epiploon (it is established on all engines except 4ZD1 and 4ZE1 on which the demountable two-section epiploon is established).


The prevention

For access to an epiploon on these engines to remove the oil pallet it is not required.


Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight. Lift the car. Establish on supports.
2. Merge oil from the engine, remove the oil pallet.
3. On cars with automatic transmission remove transmission. On cars from a manual transmission remove a check point and coupling in gathering.
4. Remove a starter, without disconnecting conducting. Take a starter aside and fix.
5. Turn away bolts and remove a flywheel.
6. Cautiously remove an epiploon, in regular intervals hooking its small screw-driver on diameter. Do not damage a neck condensed with an epiploon.
7. Fill space between working edges of a new epiploon консистентной greasing, working edges oil for the engine. Establish a new epiploon.
8. Establish a flywheel, transmission and a starter.
9. Connect the battery to weight. Start the engine, be convinced of absence of a leak.

TWO-SECTION EPIPLOON

Places of drawing of hermetic on a demountable epiploon of a cranked shaft

1 – a cover of 5th radical bearing

Both parts of an epiploon it is possible to take and replace, without removing a cranked shaft. The top and bottom parts of an epiploon should be changed simultaneously. Working edges of an epiploon should be turned towards a forward part of the engine. At installation be careful not to damage condensing platen in the channel on an external part of an epiploon. For platen protection it is recommended to use the self-made adaptation.

Removal

PERFORMANCE ORDER
1. Remove the oil pallet and a cover of the back radical bearing.
2. Get an epiploon from a back cover, having hooked its sharp tool.
3. Get the bottom part of an epiploon, having beaten out a small core so that it was possible to grasp flat-nose pliers. Thus do not damage a surface of a neck of a cranked shaft.

Installation

PERFORMANCE ORDER
1. Clear a neck of a cranked shaft and a cover of the radical bearing.
2. Grease edges of a new epiploon and condensing platen маловязким with oil so that oil has not got on epiploon periphery.
3. Place between cranked shaft and a place of landing of an epiploon the suitable adaptation.
4. Place an epiploon between the tool and cranked shaft so that the platen adjoined to the adaptation termination. Epiploon edges should be turned towards a forward part of the engine.
5. Move an epiploon on a neck of a cranked shaft by means of the adaptation which should protect the platen from damage by sharp edges картера the engine.
6. The adaptation should remain on a place until the epiploon will not occupy correct position, epiploon edges should be заподлицо with a surface of the block of cylinders.
7. Remove the adaptation.
8. Similarly establish in a cover of the radical bearing second half of epiploon. Draw in an epiploon a thumb and establish in a place.
9. Put on demountable planes of the block of cylinders and a cover of the bearing hermetic and establish a cover. Hermetic should not get on epiploon edges.
10. Tighten a cover of the radical bearing with the set moment.
11. Establish the oil pallet, fill in oil. Start the engine, be convinced of absence of a leak.