Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
      3.2.1. An electric equipment of engines
      3.2.2. Major repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and engine repair
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. A cover of a head of cylinders
         3.2.2.5. Коромысла and platens коромысел
         3.2.2.6. The thermostat
         3.2.2.7. A soaking up collector
         3.2.2.8. A final collector
         3.2.2.9. Турбокомпрессор
         3.2.2.10. The conditioner
         3.2.2.11. A radiator
         3.2.2.12. The fan of system of cooling with a drive from the electric motor
         3.2.2.13. The pump of a cooling liquid
         3.2.2.14. A head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. The oil pallet
         3.2.2.18. The oil pump
         3.2.2.19. An epiploon of a forward cover of a gear belt
         3.2.2.20. A chain of a drive of a camshaft and a drive asterisk
         3.2.2.21. A forward cover of a gear belt
         3.2.2.22. An epiploon of a cranked shaft
         3.2.2.23. A gear belt and натяжитель
         3.2.2.24. A gear belt and the tension mechanism
         3.2.2.25. A drive газораспределительного the mechanism petrol engines
         3.2.2.26. A drive газораспределительного the mechanism diesel engines
         3.2.2.27. A camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Shatunnye bearings
         3.2.2.31. Assemblage of shatunno-piston group and installation on the engine
         3.2.2.32. Заглушки and a heater картера the engine
         3.2.2.33. A back epiploon of a cranked shaft
         3.2.2.34. A cranked shaft and radical bearings
         3.2.2.35. A flywheel and a gear wreath
   3.3. The diesel engine of 2,8 litres
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes




 

Isuzu Trooper>> Engines>> Electric equipment and major repairs of engines>> Major repairs of engines>> Cover of a head of cylinders

3.2.2.4. A cover of a head of cylinders
THE GENERAL DATA

4-CYLINDER ОДНОВАЛЬНЫЕ ENGINES

Cover of a head of cylinders on 4-cylinder одновальных engines

1 – a ventilation zolotnik картера

2 – a spark plug wire

3 – bolts of a forward cover

4 – bolts of a cover of a head of cylinders

5 – a cover of a head of cylinders

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove the air filter (on carburettor engines) or an air line. (On инжекторных engines).
3. Remove a hose of a zolotnik of ventilation картера.
4. Mark and disconnect wires of spark plugs.
5. Turn away bolts of a forward cover.
6. Disconnect a hose of the vacuum amplifier of brakes and a cable of a drive throttle заслонки.
7. Turn away bolts of fastening of a cover of a head of cylinders and uncover.
8. If the cover does not give in to removal displace it, having knocked on it with a rubber hammer.

Installation

PERFORMANCE ORDER
1. Clear a place under a lining of the rests of old consolidation.
2. Establish on a cover a new lining. On a condensed surface put drops of hermetic of type RTV in diameter of 2-3 mm.
3. Establish a cover and tighten bolts with the moment 10 Н.м.
4. Establish wires of spark plugs, a ventilation zolotnik картера, a hose of the vacuum amplifier of brakes and a cable of a drive throttle заслонки (if acted in film for expansion of working space).
5. Establish the air filter or an air line.
6. Connect the battery to weight. Start the engine, be convinced of absence of a leak.

ENGINES V6

Cover of a head of cylinders on 6-cylinder engines

And – a place of drawing of hermetic

1 – nuts

2 – an intensifying plate

3 – a cover

4 – a lining

5 – hairpins

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove the air filter.
3. Remove the coil of ignition and an arm (at removal of the right cover) and the ventilation valve картера (at removal of the left cover).
4. Mark and get wires of spark plugs from an arm, strengthened on a cover hairpin.
5. Remove a ventilation zolotnik картера (at removal of the right cover).
6. Remove a cable of a drive throttle заслонки and the generator (only at removal of the right cover).
7. Turn away a nut of fastening of a cover, remove safety plates, a cover and a lining. If the cover does not give in to removal knock on it with a rubber hammer, thus do not damage фланцевую a cover part.

Installation

PERFORMANCE ORDER
1. Clear a place under a lining of the rests of old consolidation.
2. Establish a cover with a new lining.
3. Establish intensifying plates and wrap cover nuts. Tighten nuts with the moment 8 Н.м.
4. Establish a cable of a drive throttle заслонки and the generator (only at removal of the right cover).
5. Establish a ventilation zolotnik картера (at removal of the right cover).
6. Establish wires of spark plugs in an arm.
7. Establish the coil of ignition and an arm (at removal of the right cover) or the ventilation valve картера (at removal of the left cover).
8. Establish the air filter.
9. Attach the battery with weight. Start the engine, be convinced of absence of a leak.