Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. An electric equipment and major repairs of engines
   3.3. The diesel engine of 2,8 litres
      3.3.1. Introduction
      3.3.2. Technical characteristics
      3.3.3. Compression check
      3.3.4. The top dead point of the piston № 1 (ВМТ)
      3.3.5. Backlashes of valves
      3.3.6. A cover of a head of cylinders
      3.3.7. A pulley of a cranked shaft
      3.3.8. Casings of a gear belt of a drive of a camshaft
      3.3.9. A gear belt of a drive of a camshaft
      3.3.10. Asterisks of a gear belt, натяжитель and intermediate pulleys
      3.3.11. Коромысла and pushers
      3.3.12. A head of the block of cylinders
      3.3.13. Oil картер
      3.3.14. The oil pump
      3.3.15. An oil radiator
      3.3.16. Epiploons of a camshaft and a cranked shaft
      3.3.17. A flywheel
      3.3.18. Fastenings of the engine / of a transmission
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Engines>> The diesel engine of 2,8 litres>> Oil radiator

3.3.15. An oil radiator

Removal

PERFORMANCE ORDER
1. Remove a protective plate of the engine.
2. Merge cooling liquid from system of cooling of the engine.
3. Screw together the oil filter. If you have damaged the filter during removal, use new during installation carrying out.
4. Simultaneously with it merge old engine oil and fill the engine with new oil.
5. Unscrew fixing bolts and remove the thermal screen from a flange of an exhaust pipe турбонагнетателя.
6. Ослабьте fixing clips also disconnect hoses of system of cooling of the engine from an oil radiator.
7. Ослабьте also screw together lock nuts and bolts, крепящие the case of an oil radiator to the block of cylinders.
8. Remove a lining from a casing of an oil radiator and throw out it; in an installation time it will be necessary to use the new.
9. Unscrew the central bolt, крепящий a radiator lattice to a casing, and disconnect a radiator lattice.
10. Get a sealing ring from the radiator basis.
11. Throw out a sealing ring as in an installation time it will be necessary to use the new.
12. If necessary unscrew a bolt from the basis of a casing and remove the temperature valve, having taken into consideration its correct arrangement.
13. Examine the valve on presence of damages and replace it if necessary.

Installation

PERFORMANCE ORDER
1. Establish the temperature valve in the basis of a casing of a radiator (if it has been removed).
2. Check up, that joined surfaces were pure and dry.
3. Establish a new sealing ring in the basis of a lattice of a radiator and a new washer on the central bolt.
4. Insert a lattice into a casing, having tracked that the sealing ring was not displaced, then insert and tighten the central bolt till the demanded moment of an inhaling.
5. Establish a new epiploon and establish the oil filter on the block of cylinders.
6. Establish fixing nuts and bolts of a radiator and tighten them till the demanded moment of an inhaling.
7. Connect hoses to a radiator, having fixed them by means of fixing collars.
8. Establish the thermal screen on a flange турбонагнетателя and reliably twirl fixing bolts.
9. Establish the new oil filter on an oil radiator and (if it is necessary) fill in in the engine new engine oil.
10. Establish a protective guard from below the engine, then fill in cooling liquid in cooling system.