Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
   6.1. A manual transmission
   6.2. Automatic transmission
   6.3. A running gear
      6.3.1. Forward карданный a shaft, semiaxes and SHRUS
      6.3.2. An internal SHRUS
      6.3.3. Removal and installation forward карданного a shaft
      6.3.4. Dismantling карданных hinges
      6.3.5. Back карданный a shaft
      6.3.6. An average support
      6.3.7. The back bridge
         6.3.7.1. Details of the back bridge
         6.3.7.2. Removal and installation of the back bridge
      6.3.8. The forward leading bridge
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Transmission and running gear>> Running gear>> The back bridge>> Details of the back bridge

6.3.7.1. Details of the back bridge
THE GENERAL DATA

Details of the back bridge
1 – a reducer of the back bridge in gathering with the main transfer and differential
2 – bolts
3 – a lining
4 – a drain stopper
5 – a stopper control отверствия
6 – сапун
7 – a coupling bolt
8 – an epiploon
9 – adjusting linings
10 – самоподжимная a nut
11 – a washer
12 – the semiaxis bearing
13 – the holder of the bearing
14 – an epiploon
15 – полуось
16 – a wheel hairpin
17 – a drum
18 – a wheel nut
19 – a bolt of fastening of a drum to a semiaxis flange

SEMIAXES

Снятиеи installation


PERFORMANCE ORDER
1. Lift the car.
2. Remove a back wheel and a brake drum.
3. Turn away 4 bolts of fastening of a plate of the bearing of a semiaxis.
4. Get полуось a shock stripper.
5. Semiaxis installation is carried out upside-down.
6. Tighten bolts with the moment (68–81 Н.м.).

EPIPLOON OF THE REDUCER OF THE BACK BRIDGE

Removal

PERFORMANCE ORDER
1. Lift the car.
2. Put ориентационные labels and remove карданный a shaft.
3. Check up the resistance moment проворачиванию nuts of a leading gear wheel of the main transfer. At assemblage the nut should be tightened so that the resistance moment проворачиванию has remained.
The prevention

The resistance moment проворачиванию nuts of a leading gear wheel should be 27–40 Н.м.


4. Turn away a nut of a leading gear wheel and remove a washer.
5. Remove a flange of a leading gear wheel.
6. Hook and get an epiploon.
7. Clear and examine a condensed surface and a surface расточки under an epiploon in the reducer case.

Installation

PERFORMANCE ORDER
1. Запрессуйте in the reducer case a new epiploon so that the epiploon plane has appeared заподлицо with the reducer case.
2. After epiploon installation it is necessary to establish a tightness in bearings of a leading gear wheel.
3. For this purpose tighten a nut of a leading gear wheel so that the resistance moment проворачиванию nuts has remained. At a nut inhaling keep a flange.
4. Establish карданный a shaft, having combined the labels put at dismantling.
5. Check up oil level in картере the back bridge.

SEMIAXIS EPIPLOON

Removal

PERFORMANCE ORDER
1. Lift the car.
2. Get полуось.
3. Turn away a nut of the holder of the bearing.
4. Remove from a semiaxis the bearing, the holder and an epiploon.
5. Выпрессуйте an epiploon from the holder also establish the new.

Installation

PERFORMANCE ORDER
1. Tighten a nut with the moment (250–275 Н.м.).
2. Check up oil level in картере the back bridge.

REDUCER OF THE FORWARD BRIDGE

Removal

PERFORMANCE ORDER
1. Lift the car and establish on supports.
2. Merge oil from the forward bridge.
3. Put ориентационные labels remove forward карданный a shaft.
4. Remove semiaxes.
5. Turn away bolts and remove a reducer.

Installation

PERFORMANCE ORDER
1. Replace a lining and establish a reducer.
2. Fill in oil.

REDUCER OF THE BACK BRIDGE

Removal and installation

PERFORMANCE ORDER
1. Lift the car and establish on supports.
2. Merge oil from the back bridge.
3. Put ориентационные labels remove back карданный a shaft.
4. Remove semiaxes.
5. Turn away bolts and remove a reducer.
6. Replace a lining and establish a reducer.
7. Fill in oil.