Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
   6.1. A manual transmission
   6.2. Automatic transmission
   6.3. A running gear
      6.3.1. Forward карданный a shaft, semiaxes and SHRUS
      6.3.2. An internal SHRUS
      6.3.3. Removal and installation forward карданного a shaft
      6.3.4. Dismantling карданных hinges
      6.3.5. Back карданный a shaft
      6.3.6. An average support
      6.3.7. The back bridge
      6.3.8. The forward leading bridge
         6.3.8.1. Details of the forward leading bridge
         6.3.8.2. A reducer epiploon
         6.3.8.3. A nave with manual blocking of a drive of a forward driving wheel
         6.3.8.4. A self-blocked nave
         6.3.8.5. A reducer of the forward bridge
         6.3.8.6. Removal and installation of the forward bridge
7. A suspension bracket and a steering
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Transmission and running gear>> Running gear>> The forward leading bridge>> Self-blocked nave

6.3.8.4. A self-blocked nave
THE GENERAL DATA

Details самоблокируещейся naves (cars with the wheel formula 4х4)

1 – a bolt
2 – a nave cap
3 – the case and details
4 – стопроное a ring and a package of washers
5 – муфта
6 – a lead
7 – контрящаяся a washer

8 – a nut
9 – a nave and a disk
10 – the external bearing with a holder
11 – an epiploon
12 – the internal bearing with a holder
13 – a bolt
14 – a wheel hairpin

Dismantling

PERFORMANCE ORDER
1. Translate a control lever a distributing box in position 2Н. Roll the car forward and back approximately on 1 m.
2. Turn away bolts and remove a nave cap.
3. Release nuts of wheels.
4. Lift the car and establish on supports.
5. Turn away bolts of fastening of a support of a brake to a rack of a pin and fix a support a wire. Hoses of brakes not to disconnect.
6. Get a lock ring and remove a package of washers.
7. Remove муфту, a lead and контрящую a washer.
8. Ослабьте an inhaling of a nut of a nave.
9. Remove a nave from a pin.
10. If necessary press bearings easy blows on brass оправке.
11. If the brake disk put labels of mutual orientation of a disk and a nave then turn away bolts acts in film and remove a disk.

Assemblage

PERFORMANCE ORDER
1. Assemblage is carried out in return sequence.
2. Adjust an inhaling of a nut of a forward wheel in a following order:
2.1. Tighten a nut of a nave with the moment 27 Н.м.
2.2. On return a bolt on a hairpin of a wheel and establish a dynamometer.
2.3. Tighten a nut before tightness creation in bearings approximately at 18-22 Н if new bearings and an epiploon are established, and 8–16 Н if bearings and an epiploon did not vary.
3. Adjust axial люфт naves in a following order:
3.1. Establish on a nave special оправку against the stop in контрящую a washer.
3.2. Measure щупом a backlash between a nave and a flute of a lock ring on a semiaxis.
3.3. If the backlash exceeds width of a flute for a lock ring pick up a package of washers of such thickness that the backlash was within 0–0,1 mm.
4. Grease bolts of a cap of a nave with structure fixing from отворачивания and tighten bolts with the moment 60 Н.м.