Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
   7.1. A forward suspension bracket
   7.2. Corners of installation of wheels
   7.3. A back suspension bracket
   7.4. A steering
      7.4.1. A steering wheel without a safety pillow
      7.4.2. A steering wheel with a safety pillow
      7.4.3. The switch of the index of turn (the combined switch)
      7.4.4. A key of the switch of ignition and the lock of blocking of a wheel
      7.4.5. The lock of blocking of a wheel
      7.4.6. A steering column
      7.4.7. Steering draughts
      7.4.8. The steering mechanism
      7.4.9. The steering mechanism with the hydraulic booster
      7.4.10. The hydraulic booster pump
8. Brake system
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Suspension bracket and steering>> Steering>> Steering draughts

7.4.7. Steering draughts

LATERAL DRAUGHTS

Removal and installation

PERFORMANCE ORDER
1. Lift the car and remove forward wheels.
2. Расшплинтуйте корончатую a nut of a tip of draught, turn away a nut. Выпрессуйте a tip from an eye of a pin also disconnect draught.
3. Put a label on a carving part of draught (a paint or wind with a tape). Turn away a counternut and turn out draught from steering рейки.
4. Wrap draught to a label put at dismantling. Tighten a counternut with the moment 34 Н.м.
5. Insert draught into a pin eye. Tighten a nut of a tip with the moment 39 Н.м., tighten a nut to insert шплинт. Шплинт replace.
6. Establish forward wheels and lower the car.
7. Check up and adjust corners of installation of wheels.

INTERNAL DRAUGHT (GEAR РЕЙКА IN GATHERING WITH THE STEERING MECHANISM)

Removal

PERFORMANCE ORDER
1. Remove gear рейку in gathering with the steering mechanism (subsection 7.4.8 see).
2. Turn out lateral draught and remove a dustproof cover.
3. Clamp рейку in a vice with soft sponges.
4. Straighten a lock washer hammer blows on a chisel.
5. Turn out internal draught.

Installation

PERFORMANCE ORDER
1. Wrap internal draught with the moment 88 Н.м., establish a new lock washer.
2. Tyre out a lock washer a hammer and a chisel.
3. Put on a dustproof cover and establish lateral draught with a tip.
4. Establish gear рейку in gathering with the steering mechanism (subsection 7.4.8 see).

AVERAGE DRAUGHT AND РЕЙКА THE MECHANISM WITH THE WORM STEERING REDUCER

Removal

PERFORMANCE ORDER
1. Lift the car and establish on supports.
2. Расшплинтуйте spherical tips of intermediate draught in a place of a joint with сошкой a wheel and the shock-absorber. Turn on корончатые nuts. Выпрессуйте tips from eyes of average draught.
3. Turn away a nut and remove контрящую a washer from tips of average draught, выпрессуйте a tip of average draught from the pendular lever.
4. Remove average and lateral draughts.
5. If average draught varies, remove lateral draughts.

Installation

PERFORMANCE ORDER
1. Clear a carving of tips of draughts. Check up a carving condition on which there should not be broken threads.
2. Establish average draught on the pendular lever and tighten a nut with the moment 65 Н.м.
3. Raise draught and establish on сошку, tighten a nut of a tip with the moment 55 Н.м. Tighten a nut and establish new шплинт.
4. Connect draught to the shock-absorber, tighten a nut with the moment 105 Н.м. Tighten a nut and establish new шплинт.
5. Establish lateral draughts in tips of average draught and tighten nuts with the moment 55 Н.м. Tighten nuts and establish new шплинты. Grease the carving terminations of tips of draughts.