Isuzu Truper - Isuzu Trooper
1. The maintenance instruction
2. Maintenance service
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and a running gear
7. A suspension bracket and a steering
8. Brake system
   8.1. Adjustment of drum-type brakes
   8.2. A pedal
   8.3. The switch of a signal of braking
   8.4. The main cylinder of brakes
   8.5. The vacuum amplifier of brakes
   8.6. Dosing out valves
   8.7. Hoses of brakes
   8.8. Removal of air from a hydrodrive of brakes
   8.9. Disk brakes
   8.10. A brake support
   8.11. A brake disk
   8.12. Drum-type brakes
   8.13. Antiblocking system of brakes of back wheels
   8.14. Specifications of brakes
9. A body
10. A body electric equipment
11. Diagnostics of malfunctions
12. Electroschemes





Isuzu Trooper>> Brake system>> Removal of air from a hydrodrive of brakes

8.8. Removal of air from a hydrodrive of brakes
PERFORMANCE ORDER
1. Put the car on a manual brake and start the engine.
2. Turn away a stopper of a nutritious tank and add a liquid to top. In the course of prorolling of brakes liquid level support approximately on the tank middle.
3. If the main cylinder acted in film and understood, remove air from the main cylinder and from each wheel cylinder. Air from the main cylinder leaves in a following order:
3.1. Disconnect from the main cylinder a tube of a highway of the left forward wheel.
3.2. Ask the assistant to press and keep a brake pedal.
3.3. Clamp a finger an aperture of the union of the disconnected tube and ask the assistant to release a pedal slowly.
3.4. After full отпускания pedals clean a finger from an aperture.
3.5. Repeat procedures 3.1–3.4 until from an aperture the liquid will not pour down.
3.6. Attach a tube to the main cylinder.
3.7. Ask the assistant to press and keep a brake pedal slowly.
3.8. Release the union of a tube of a hydrodrive of the wheel cylinder on the main cylinder.
3.9. Again tighten the union and ask the assistant to release a pedal slowly.
3.10. Repeat procedures 3.7–3.9 until the weakened connection will not cease to leave air.
3.11. Having repeated procedures 3.1–3.10, remove air from a highway of the right forward wheel.
4. Remove air from wheel cylinders in a following order: the left forward, right back, right forward, left back.
4.1. Dress on the union for prorolling of brakes накидной a key.
4.2. Dress on the union a transparent hose, other end of a hose ship in a vessel with a brake liquid.
4.3. Ask the assistant to press three times a pedal brakes, then to press and keep.
4.4. Turn away the union and let out a liquid containing air.
4.5. Again tighten the union and ask the assistant to release a pedal slowly.
4.6. Repeat procedures 4.3–4.5 until air will not leave from a highway. As a rule it is required to repeat not less than 10 times at prorolling of forward wheel cylinders, or not less than 15 times at prorolling of the back.
4.7. Remove air from other wheel cylinders, having repeated the described procedure.
5. After the prorolling termination press a brake pedal. If air is completely removed from a hydrodrive the pedal should be "rigid". If a pedal "soft" it is necessary to repeat all procedure of prorolling.
6. After the prorolling termination press a brake pedal. If air is completely removed from a hydrodrive the pedal should be "rigid". If a pedal "soft" it is necessary to repeat all procedure of prorolling.
7. Put into place a stopper of a tank and stop the engine.